Search Results

Overview The data collector plugin allows you to track the state of a signal between multiple runs of Mach4. For example, you can fault out after 1000 hours of the spindle running.  To reset from a fault, press the user button on the screen. That will make i...

Tool X and Y Offsets Select View->Tool Tables... You will see the tool table.  Select Edit->Table Fields. You will see the Tool Table Editor.  Select the Optional Field Tab.  Then select the key name XOffset and press Move Pri. Repeat for the YOffset. ...

Running a G-Code File with the "File Resume" or "Run From Here" Option If for whatever reason a program needs to be started in the middle, use the Run From Here feature by following these steps: Use the Up/Down arrows in the G-Code file window to select th...

1. Introduction 1.1 Control Startup To open the control software double-click on the profile icon on the desktop. 1.2 Overview This manual gives the process for basic operation of the 2000 Series Surface Grinder control. The screen is shown below, foll...

Sigma 7 Pulse and Direction Drive Wiring Wire the analog input to the analog monitors on CN5.  Use a cable as shown below: Setup Options Factor and Offset Load Meter Analog Monitor 1 Pn006=.XX02  Calculate the value of Pn552 based on t...

Setup Motor setup: Input the motor parameters into the drive according to the motor nameplate Dn.00 = rated current of motor Dn.01 = rated speed of motor Dn.02 = rated voltage of motor Dn.03 = rated power of motor Dn.04 = motor power facto...

400W TECOs Because 400W cables and the original 400W motors without a gearbox are no longer available, use the following process to upgrade a 400W system.  If the motor, encoder cable, or power cable fails, you always have to replace all 3. For example, if a...

MachMotion uses Dold safety relays on many electrical enclosures to provide the right level of safety needed in an emergency condition.  Delayed Safety Relay vendor part BH5928-92-61-24-30, MachMotion P/N 170323 A delayed safety relay is used to allow time...

Setup Below are the main plugins used for Modbus Control.  Configure -> Plugins -> MachMotion Modbus Plugin.  Configure -> Plugins -> Modbus   Troubleshooting Modbus will automatically re-connect if it disconnects.         

  Links below: 2000 Series General Installation Manual 2000 Series Knee Mill Installation Wireless pendant manual X15-62-00 2000 Series Mounting Arm X15-62-04 Bottom Arm Mounting Instructions 2000 Series Apollo III Operating Manual 2000 Series Commands...

Drill Bank Example Drawing The numbers 20-29 are straight drills and the numbers 14-19 are horizontal drills.  Drill Bank 1 Setup Map all overall drill bank features according to the requirements for the drill bank to begin and end a cycle NOTE: Every ...

The following list of tools is required for most installations: Tachometer (for any machine with a spindle) Voltmeter Wrenches, torque wrenches, etc. for all mechanical work Dial indictor for backlash and unit setup 

Remove From Case and Connect Hardware 1) Place keyboard, mouse pad, and mouse in the control tray.   2) Screw the magnet into the bottom of the camera. Then Mount the Camera on the top left of the control. It should look like this.  3) Plug in the Cam...

Standard Setup Jet Setup Configure the number of jets you need and your default delays.  You may try setting the Jet Abrasive Purge Line Delay at 1250 ms which allows the abrasive to stop flowing just before the water turns off. Also set the Jet Off Delay...

Below is the standard setup for any 2000 series centerless Grinder Axis Setup Axis Names Axes Directions Grind Dress X Axis Traverse - 0.00 Is out away from the wheel towards the front and moving toward the wheel is positive. Grind Dress Y Axis Di...

Log into wordpress under your own account (assuming you're a partner account).  Navigate to machsupport.com. Go to the cart.  Apply the coupon for swift (if it's a swift PO): swiftoem5 Update quantity. Checkout. Select Create Registration Codes only.  ...

Please use the picture below as a guide to generate NC code for your machine. After generating the code, check it by running it on your machine. THIS CODE MUST RUN ON YOUR MACHINE AND PERFORM AS EXPECTED.   STL File: 3D Part Drawing See the overview drawin...