Advanced Search
Search Results
80 total results found
MachPro Tool Setter Wiring and Testing
Normally Open (NO) probing with Normally Closed (NC) overtravel Scope This document describes how to wire a PHM2P (P) probe to a CNC controller and how to configure two controller inputs: Probe trigger input (Normally Open output). Overtravel ...
MachPro TP400 Probe Wiring to M31 Motion Controller
How-to guide Scope Wire a TP400 touch probe to an M31 DI (Digital Input). Configure the TP400 output as NO or NC by swapping the TP400 power wire polarity. Definitions DC (Direct Current): Electrical current that flows in one direction. DI (Di...
MachPro Input Mapping for Tool Setter and Probe
Purpose This document tells you how to map (assign) a physical input to a MachPro probing signal for: a tool setter (tool length measurement switch or plate) a probe (part probe, touch plate, or ohmic probe) Definitions I/O: Input/Output...
MachPro Compatible Motion Controller Configuration Settings
This manual will guide you through integrating your compatible motion controller with MachPro. If you purchased your motion controller from MachLabs, integration documentation is available here MachLabs recommends using the E-Stop, Hardware Enable, Drive En...
MachPro Import Mach3 or Mach4 Configurations
The MachPro package installer can import the configuration files from Mach3 and Mach4. Verify your current settings in Mach3 and Mach4. Ensure that any changes are running as you expect them to. Mach3 and Mach4 need to be closed down during the import...
PoLabs PoKeys Motion Controllers
MachPro 26 CNC Software Roadmap This installation is a two-step process. During the MachPro package installation, the PoLabs plugin was copied to your hard drive. The first step of the installation is to now configure that plugin. The second step is to us...
ESS Motion Controllers
MachPro 26 CNC Software Roadmap Plan your network configuration At times a CNC computer has a very heavy resource load while it is running. We recommend you set this computer to be used primarily for CNC control. The network communication with the motion c...
SOURCE: Blum Probing Operation
MachPro Version 2026.5.13.1 and greater Prerequisites Install and configure your probe according to the manufacturer's documentation Map the inputs to the appropriate MachPro signals MachPro incorporates the Blum Edge Finding macros to p...
MachPro Blum Probing Routines
SOURCE: Languages
MachPro Version 2026.5.13.1 and greater You may change the display language for the MachPro screen labels and buttons. This is an English-to-target-language word mapping feature, and you may freely switch between available languages. We will add ...
SOURCE: MachPro Probing Wizard
MachPro Version less than 2026.5.13.1 Edge and Angle Finding The Edge Finding tools are available on the Fixtures Tab -> Edge Finding. Edge Finding Settings Edges have two options for when the probe makes contact. The work offset can be ze...
Geckodrive G540 Drive Wiring
Printable PDF versions of each of these diagrams are available in the upper left area of this browser window, or under the Info tab on a smart phone.Clicking on an image will open it in a new tab or window and you can zoom in to see details. M31 M...
MachPro GCAdapter
1. Introduction Overview The GCAdapter is a highly customizable post that works inside of Mach 4 that changes GCode to Mach compatible GCode. This manual will describe how to use the GCAdapter. File Locations GCAdapter.lua In the Mach4 directory, GCA...
MachPro Plate Alignment and Transform Functions
Plate Alignment Plate alignment provides a simple way to accurately rotate your work offsets to match the work piece on your table. Often large work pieces are not perfectly square on the table, and this tool solves that problem. First steps Remove G69 (...
MachPro File Resume and Cut Recovery
There are many scenarios when you will need to stop a running job, and there are different ways to gracefully resume the job so that you do not have to scrap the work piece. A cutting tool breaks A plasma cutter lost the arc A water jet tip needs to be ...
MachPro Spindle Configure for M31 up to Rev 1.2
Analog 0-10V and sinking outputs for spindle control M31 Motion Controllers prior to Rev 1.3 use sinking outputs to control the CW and CCW direction of rotation on the spindle. Using 0-10VDC to control the speed, and sinking outputs to control the rotation ...
MachPro RapidChange Tool Changer and Tool Setter
MachPro Version 2026.5.13.1 and greater RapidChangeATC provides a family of tool changers that work with a wide range of machines that do not have a traditional tool changer option. RapidChangeATC Resources RapidChange ATC Website Rapid...
MachPro M31 Enable Absolute Encoder
If this is on a gantry with master and slave motors, configure the gantry first, then enable the absolute encoders. Explanation The MachPro M31 motion controller can use an absolute encoder to keep an axis position after the machine is powered off. An a...
Gantry Alignment with a Slave Axis
Updating for M31 2026-05-12-T16-06 This needs to be merged into a single master slave setup, homing, aligning doc This only applies to master and slave axes on a gantry. If you are trying to align the tables on a dual table router, pull down Configure -> Con...
MachPro M31 Configuring a Master Slave Axis Gantry
This only applies to master and slave axes on a gantry. If you are trying to align the tables on a dual table router, use the home offsets in MachPro. Pull down Configure -> Control -> Homing / Soft Limits tab. If you have absolute encoders, either configure...