Architectural Grille Configurable Parameters

Standard Parameters

Sub-Category	Name	Description	Comments
Machine Data	LCM_DataDir	Data Directory	where the CSV data files are stored These are used for calculations.
Post	LCM_MaxSpacing	Maximum Spacing between Center of Notches	threshold used in calculations
Post	LCM_SafeStartLine	Safe Start Line	The safe start block(s) used in generated G code files. machine-specific
Post	LCM_TrimLength	X length to trim to square leading end of material	amount of material to remove when trimming the leading edge (to make all material flush)
Post	LCM_ProbeFeedRate	Feed rate for probe moves
Post	LCM_DrillFeedRate	Feed rate for drill moves
Post	LCM_DrillRPM	RPM for drilling
Post	LCM_PusherFeedRate	Feed rate for pusher moves
Post	LCM_FeedDirection	Direction the machine feeds
Post	LCM_SawCutFeedrate	Feed rate for saw cuts
Post	LCM_SawSpindleSpeed	Spindle Speed for Saw Cuts (RPM)
Post	LCM_DoorPivotMatchesFeedDir	Door pivot type matching feed direction	compare with LCM_FeedDirection; This affects how the doors are oriented.
Wizard	LCM_JobList_ShowWorkspace	Show Workspace in Job List	For machines with work spaces, show the workspace in the job list
Wizard	LCM_EnableWorkspaces	Enable Workspaces	whether or not the machine has multiple "work spaces" for shaped bars (non AG-10) vs. rectangular bars (AG-10)
Probe	LCM_ProbeOffset	Distance from X0 to the probe trigger position	When the probe strikes, the X fixture offset is changed. This distance is used in that calculation.
Drill	LCM_PerformDrillOperations	Perform drill operations	whether or not the machine has (or performs) drilling
Drill	LCM_DrillOffset	Distance from saw blade center to the center of the drill bit	used to calculate where to move the material to in order to perform a drill operation
Drill	LCM_DrillClearanceZ	Z position for the drill to avoid any material	clearance position for the drill
Drill	LCM_DrillDepthClearance	Distance past the material to drill	To ensure that the final hole(s) are completely drilled, this amount is commanded in addition to the position of the last bar for a drill operation.
Saw	LCM_SawClearanceY	Y position for the saw to avoid any material (G53)	clearance position for the saw
Saw	LCM_SawCutoffY	Y Amount Added to Height for a cut-off	additional height to command the saw when performing a cut-off operation (as opposed to cutting notches)
Saw	LCM_SawKerfWidth	Saw Kerf Width	the actual width of the saw kerf—not just the blade width
Saw	LCM_SawDiameter	Saw Diameter	Used to calculate saw Y position to get precise notch depth
Saw	LCM_SawXPosition	Saw Position (machine coordinates)	the X position of the unfinished edge of the saw blade
Pusher	LCM_PusherMinimumX	Minimum X position to command the pusher	the closest (smallest) X position the pusher/feeder should be commanded to
Pusher	LCM_PusherLoadOffset	Pusher Load Offset From Saw
Pusher	LCM_PusherRetractPosition	Pusher Retract Position (machine coordinates)
Shapes	LCM_ShapesClampsSpace	Distance Between Shapes Clamps (W)
Shapes	LCM_ShapesSawCutWEnd	W Start Position for Shapes Saw Cut
Bundles	LCM_BundlesSawCutWEnd	W End Position for Bundles Saw Cut
Workspace	LCM_EngageTableClampsInJob	Enable the Table Clamps/Supports in a Job
Signals	LCM_WorkspaceShapesOutput	Signal to Enable Shapes Supports
Signals	LCM_ForceTableClampDisengage	Signal to Force Clamp Disengage
Signals	LCM_TriggerAutoEngageOutput	Signal to Trigger an Automatic Clamp Engage
Signals	LCM_TableClampsStateOutput	Signal represeting the Table Clamps State
Options	LCM_HasOutfeedClamps	Machine has outfeed clamps	whether or not the machine has outfeed clamps The G code and user commands needs to know if they exist in order to [dis]engage them.