Electrical

View electrical drawings and diagrams related to MachMotion equipment.

Converters

Converters

X15-02-02 Step & Direction Single Ended to Differential Converter

 

File Type Document Name View / Download / Print
pdf-icon.png X15-02-02 Step & Direction Single Ended to Differential Converter

 

 

Keywords: Mach Step direction Single converter

 

 

Converters

X15-02-03 Step & Direction Differential to Single Ended Converter

 

File Type Document Name View / Download / Print
pdf-icon.png X15-02-03 Step & Direction Differential to Single Ended Converter

 

 

Keywords: Mach mach4 mach4 pin out diagram

 

 

Converters

X15-02-04 Encoder Single Ended to Differential Converter

 

File Type Document Name View / Download / Print
pdf-icon.png X15-02-04 Encoder Single Ended to Differential Converter

 

 

Keywords: Mach4 Mach 3 converter encoder

Converters

X15-02-05 Encoder Differential to Single Ended Converter

 

File Type Document Name View / Download / Print
pdf-icon.png X15-02-05 Encoder Differential to Single Ended Converter

 

 

Keywords: Mach4 Mach 3 converter encoder

Standard Operating Conditions For Electrical and Control Equipment

__Use__MachMotion_Logo_HiRes_TransBG-update-01-450.png


 

This document specifies conditions within which MachMotion electrical and control equipment products
can operate. Other conditions may be accommodated with additional engineering.


ENVIRONMENTAL
  1. Enclosure type: NEMA/UL type 1 (Where enclosure is provided by MachMotion)
     Indoor use only. Enclosure “provides a degree of protection against: a) incidental contact with the
    enclosed equipment, and b) against falling dirt”.
  2. Ambient temperature range: 5̊C to 40̊C (41̊F to 104̊F)
  3. Humidity range: 0% to 85% Relative Humidity (RH) maximum, non-condensing
  4. Altitude: 1000 meters (3280 feet) maximum above mean sea level
  5. Environment:
    a. Pollution Degree 2
    b. Free of flammable or corrosive gases or mists
    c. Minimal non-conductive dusts (1 ppm or less) in ambient air
    d. Free of salts or iron dust
    e. Free of water (including rain and snow), oil, or chemical mists
  6. Environmental radiation:
    a. Free of strong electromagnetic or magnetic fields
    b. Free of static electricity
    c. Free of ionizing radiation
    d. Not located in direct sunlight
  7. Vibration and Mechanical shock:
    a. Vibration: 4.9 m/s2
    (0.5 G) maximum
    b. Shock: 19.6 m/s2
    (2 G) maximum

 


ELECTRICAL POWER SUPPLY
  1. Voltage fluctuation from nominal: +10%, -10% maximum
  2. Frequency fluctuation from nominal: +2%, -2% maximum
  3. Prospective short circuit current: Standard: 5,000 amps, RMS.
  4. Voltage, phase, frequency: Standard: 230 volts ±10% AC, 3 phase, 60 Hertz.
    a. Other supply characteristics available upon request:
    b. 230 volts ±10%, 1 phase, 50 or 60 Hertz
    c. 120 volts ±10%, 1 phase, 50 or 60 Hertz
    d. 400Y/231 volts ±10%, 3 phase, 50 Hertz (grounded Y connection only)
    e. 480Y/277 volts (440-480 volts), 3 phase, 60 Hertz (grounded Y connection only)
    f. 480 volts Delta, 3 phase – Not directly supported. A suitable transformer is required.

Neutral connection:

  1. Connection to the grounded supply conductor (i.e., the Neutral) is not required, unless noted by a
     decal at the power supply terminals or the manufacturer’s name plate.
  2. The Neutral connection and the Ground connection are for distinct functions. They are not intended to be connected together (except at the premises power supply grounding point.)

 

Grounding

Grounded Power supply. The equipment is designed for connection to a solidly grounded power
supply. See Voltage and Phase, above.

Frame grounding

The non-current carrying parts of the frame shall be effectively grounded, by
connection to the premises equipment grounding (protective earthing) conductor. An equipment
grounding connection point is provided near the supply circuit connection point. Isolated ground
rods shall not be used. If local ground rods are used, there shall still be a connection to the
premises equipment grounding (protective earthing) conductor.

Overcurrent protection of supply conductors: not provided (standard). Data for selection of the
overcurrent device(s) is located on the manufacturer’s name plate.

Type of disconnecting device: Standard: Non-fusible panel disconnect, UL 508, IEC 60947-3. Selectorstyle
external operator handle, lockable, prevents opening door when energized, defeatable with a tool.

Operator station power supply: Operator station requires 100 to 264 volts, 1.5 ampere max, single
phase AC. The operator station can be powered from the main electrical panel (by connecting to the
operator station power cable), or it can be powered separately, e.g., from a wall outlet or uninterruptible
power supply.


OTHER CONSIDERATIONS


Markings

MachMotion control and electrical products have hazard markings that generally meet US
federal and Canadian standards, and have MachMotion brand marks. Other markings available.
Certification markings are available for an additional fee.


Technical documentation is furnished in paper form, with electronic copies (PDF format) on the
system’s operator station PC. Further documentation is available on our website –
support.machmotion.com

Commander SK Advanced User Guide

 

File Type Document Name View / Download / Print
pdf-icon.png Commander SK Advanced User Guide

 

Keywords: AC alternating Current motor alternating manual manufacturer specs digital-manual digital 

Control Internal 24VDC Power Supply

Description of the problem:

What is the maximum power output of the 24VDC power supply in the control?
 

Solution:

The 24VDC power supply in the PC provides a max power of 35W. 

 

Keywords: 7622